- #Standard sata ahci controller driver for windows creator how to
- #Standard sata ahci controller driver for windows creator install
- #Standard sata ahci controller driver for windows creator full
- #Standard sata ahci controller driver for windows creator verification
Connect a different preformatted SATA drive to the same data and power connectors that were previously connected to SATA-01. Note that having a second IDE drive present when switching to AHCI mode is possible, but it introduces additional opportunities for operator error.Ħ. Put the CD-ROM/DVD drive(s) on the other cable and configure the jumpers appropriately (i.e., one Master and the other Slave, or just use Cable Select for both). If your motherboard has two IDE ports (usually one cable for two hard drives and the other cable for two CD-ROM/DVD drives), put the IDE drive on one cable by itself and set its jumpers to Single (or Master with Slave Present if you have two IDE drives). If your motherboard has only one IDE port, set the IDE drive to Master with Slave Present and the CD-ROM/DVD drive to Slave (or set both to Cable Select). Connect an IDE drive of suitable byte size to an available IDE cable. I recommend that you remove the boot drive and set it aside for safety reasons.ĥ. You can either remove the boot drive or leave it in the machine. Mark the boot drive with tape or a label that says SATA-01. Shut down and physically disconnect the data and power connections to the SATA-01 boot drive. I once had a restore operation hang because of a bad destination disk and the hang corrupted the backup image.Ĥ. Instead, make a copy of it and use the copy for the restore operation. If an error occurs, you shouldn't use the second backup image for the restore operation.
![standard sata ahci controller driver for windows creator standard sata ahci controller driver for windows creator](http://3.bp.blogspot.com/-1YvsmvCihmQ/T2nUQsRelnI/AAAAAAAAAYY/bEjhzvX5LIE/s1600/p5.jpg)
This second backup image isn't needed for the switch, but it provides an extra layer of protection in case of operator error. Once again, verify 100 percent integrity of the backup image.
#Standard sata ahci controller driver for windows creator full
Make another full disk backup image of the SATA-01 boot drive, saving it to a different spindle (e.g., G:\ SATA-01\SATA-01.tib, G:\ SATA-01\SATA-01.gho) or removable drive.
#Standard sata ahci controller driver for windows creator verification
Make certain to use the imaging program's verification function to verify 100 percent integrity of the SATA-01 backup image.ģ.
![standard sata ahci controller driver for windows creator standard sata ahci controller driver for windows creator](https://powerfuldb615.weebly.com/uploads/1/2/6/4/126436479/749575690.png)
Using an imaging program (e.g., Acronis True Image, Symantec's Norton Ghost), make a full disk backup image of SATA-01 and save the image to a different spindle (e.g., F:\SATA-01\SATA-01.tib, F:\SATA-01\SATA-01.gho) or removable drive. Put the driver files into a new directory (e.g., C:\ICH9R) on the existing SATA boot drive, which I'll refer to as SATA-01.Ģ.
![standard sata ahci controller driver for windows creator standard sata ahci controller driver for windows creator](https://users.wfu.edu/yipcw/lenovo/2012/T430s/review/images/t430s-programs-oem.gif)
Alternatively, for well-known manufacturers, you might be able to find the F6 driver files for your chipset by searching the web (e.g., search for "F6 ICH9R"). For example, on an ASUS P5E3 motherboard CD-ROM, the files for the Intel ICH9R SATA controller are found in D:\Drivers\Chipset\Makedisk\DOS\32bit (or \64bit).
#Standard sata ahci controller driver for windows creator install
(They're referred to as the F6 driver files because they were the files that you'd put on a floppy disk and use during a Windows OS installation when prompted to Press F6 if you need to install a third party SCSCI or RAID driver.) You can download the driver files from your motherboard manufacturer's website or use the files found in the motherboard's installation CD-ROM. Download the "F6" driver files for your SATA controller chipset. If your motherboard has an IDE port, switching is relatively simple. If you're running Windows XP, you're not out of luck. If you're running Windows 7 or Windows Vista, there's a registry tweak to switch to AHCI mode, which I haven't tried yet. AHCI exposes SATA's advanced features, including reduced CPU overhead and hot-plug and power-management capabilities.
#Standard sata ahci controller driver for windows creator how to
I've seen much discussion on the web about how to switch the BIOS Serial ATA (SATA) boot drive from IDE mode to Advanced Host Controller Interface (AHCI) mode in existing Windows installations.